Express Shop!
Search Our Stuff
View Cart (0)
Sign In/Up! (It's Worth It!)
Image Viewing Preferences
You now have the option to view our web site with dazzling color photos or with our traditional hand-drawn line art. It’s a big decision, but don’t worry; you can always change your mind later. Choose your path below. Thanks! If you have a sciplus.com web account we can remember your changes. Sign in to your account or create an account.
Linear Actuator
New linear actuator from Von Weise®, made for sliding camper sections, has a motor approx 6-1/2" x 3" x 6-1/2" overall. Draws 11A at 12VDC under load, 1.25A no load, and spins approx 150 rpm. Has 4" leads with a 2-pin connection. Output is through a 3/4" dia threaded rod inside a 1-3/8" dia steel pipe. You pick from the short version, a 33-3/4" long pipe (37" long over all); the medium, a 35-1/2" pipe (38" long over all); or the long, a 41" pipe (44" long over all). All have approx 30" stroke.
 |
39936 12VDC LINEAR ACTUATOR Note: This item is not eligible for Expedited Shipping or delivery to Alaska, Hawaii, or the Territories. |
|
|
39934 LONG ACTUATOR Note: This item is not eligible for Expedited Shipping or delivery to Alaska, Hawaii, or the Territories. |
|
|
39935 SHORT ACTUATOR Note: This item is not eligible for Expedited Shipping or delivery to Alaska, Hawaii, or the Territories. |
Move Your Butt
These brand-spanking new 12VDC motors are made to move automobile seats but are willing to change. They spin at approx 190 rpm, draw 1.5A no load, and stall at approx 25A. Threaded shaft is at a right angle and is 4-1/8" x 7/16". Shaft thread is non-standard, so treat it as a smooth shaft and mount pulley or gear with a setscrew. Measures 5-5/8" x 2-1/2" x 2-1/2" overall, not counting the shaft, and has power terminals opposite the gearbox with (2) 1/4" mounting holes opposite the shaft.
|
40588 CAR SEAT MOTOR |
Gear Motor
Attention robotics boffins: Here's a nice, powerful 12-24VDC Mabuchi brush motor with a gearbox and pulley attached. At its nominal 24DC, it spins 45rpm, draws 280mA no load, and stalls a 750mA. 7.5 in-lbs of torque and is rated for continuous duty. Has a 3/4" long x 5/16" flattened shaft with a 4-5/8" dia x 5/16" wide (3/16" ID) single-sheave pulley attached, with a matching O-ring. The gearbox measures 2-3/4" x 3" x 9-1/16". The motor measures 1-1/16"dia x 1-5/8" long and comes with 7" leads and a 2-pin Molex connector.
|
37837 MOTOR W/PULLEY |
Tough Guy Motor
This sturdy little gear motor is nominally rated for 19.1VDC, but at 12VDC it will be a 250mA no-load draw and stall at 1A. Spins 50 rpm, through a 5/8" long x 3/16" dia shaft with a 30-tooth, approx 21/32" x 7/32" (17mm x 5.5mm) gear. Has a 1-3/4" x 1-3/8" mounting plate with a corner knocked off. Motor measures 3" long x 1-3/8" dia at the widest, with 4" leads. Made in the USA by Pittman®.
|
40474 TUBULAR GEAR MOTOR |
12 VDC Linear Actuator
This motor on this 12-volt linear actuator is 6" x 3" x 6" overall. Output is through both a 2-draw mast that measures 2" dia at bottom, with a flattened 3/4"-10 threaded rod that extends 5-1/2" past the top draw and a keyed 1-1/4" long x 5/8" hex shaft below the gearbox (approx 400 rpm). Draws 4.5A at 12VDC no load, stalls at 30A. Retracted length is 35", extended length is 66" counting the rod and hex shaft. Stroke approx 30".
|
39958 12 VDC LINEAR ACTUATOR Note: This item is not eligible for Expedited Shipping or delivery to Alaska, Hawaii, or the Territories. |
$109.50
EACH
Out of Stock. Check Back Soon! |
B-17 & B-24 Motors
These small, new motors for oil-heater louvered doors were made for, but never installed in, WWII-era B-17s and B-24s. High torque, low rpm, these collectible 24VDC 1.5A motors measure 5-1/8" long x 3-1/2" dia on the shaft side and 2-3/8" dia on the other end, in a blunted bullet shape. The 15-tooth output shaft is 3/4" long x 1/2" dia, centered on the large end with a trim screw offset for some speed control, and a 4-pin Amphenol connector. Rated at 24VDC but will operate between 12-26VDC. These are of particular interest to us because the sample, at least, was manufactured right down the road from us in Rockford, Illinois, by the Barber-Colman Company!
|
39972 WW II B17/B24 AIRCRAFT CONTROLLER MOTOR |
Popular Tags:
Fun
Homeschool
ctw
|
Add Tag 
Takeout Hitachis
The 24 VDC Hitachi stepper motor is labeled with Kodak’s part number 315871. Each has 1:5 gearboxes, (3) Hall–effect sensors, and 12 steps per revolution (without the gearbox). The motor cases are 1–3/4” thick x 3–5/8” dia. The 2–1/2” sq x 15/16” thick gearboxes terminate in 1” x 3/8” dia flattened shafts with mounted plastic cams. Each has a set of (7) and a set of (3) leads with Molex–type connectors. The motor draws 2.4 amps. Sorry, folks, that’s all we know.
|
34589 2.4 AMP STEP MOTOR |
Shop by Popular Tags
Click a phrase to shop for products associated with that phrase (AKA "Tag"). More popular tags appear bigger. Learn more »
