Express Shop!
Search Our Stuff
View Cart (0)
Sign In/Up! (It's Worth It!)
Home
/ Switches
Wanna Toggle?
The correct answer is "I don't know; I've never toggled." If, however, you just want to turn something on and off, here's a choice of toggles for your switching delectation. The DPDT toggle is rated for up to 20A at 125VAC and has screw terminals below. Measures 1-1/4" x 1-3/4". No center-off position. The first DPST toggle is rated for 20A at 125VAC or 15A at 250VAC. Screw terminals on the bottom. Measures 1-5/16" x 3/4". The smaller DPST toggle is rated for up to 4A at 125VAC or 2A at 250VAC. Has 3/16" spade terminals on the bottom and measures 1" X 9/16". All the toggles come with switch-plates and mounting nuts.
 |
38715 DPDT TOGGLE 20A (A) | |
|
38716 DPST TOGGLE 20A (B) | |
|
38717 DPST TOGGLE 4A (C) |
Take The Plunge
You'll need a little plunger solenoid, of course. Ours has a nominal voltage of 24VDC but works fine at 12VDC. At 24VDC, it has an approx 1" pull. Measures 1-5/8" x 1" square with a 5/16" dia x 1-5/16" long plunger, which has a small hole through it near the end. Draws 300mA at 24VDC and the back has a pair of mounting holes on a plate that extends beyond the 1-5/8" edge.
|
38815 PLUNGER SOLENOID |
Green Means Go
It's an on/off SPST key switch with dual indicator lights, and even if you don't need it as is, the parts are little treasures on their own. A standard round key switch and small rectangular LEDs, (1) red and (1) green, are connected to an 8-pin connector by 8-1/2 leads. The red LED also has 14" leads to a 2-pin connector. Requires 3 VDC. Comes with (2) keys. All are keyed alike.
 |
34659 KEY SWITCH |
Relay
Electromagnetic-type relay for your circuitry work. Encased in plastic, it's 1-1/4" x 1-1/8" x 3/4", with (5) pins on the bottom. NO/NC, 3VDC, SPST. Works great with a couple of AA batteries (which are not included). Marked "601-595G, 40-463, CDE1077." Instruction sheet included.
|
27803 RELAY, 3VDC |
Reed Switches
Pick a 10- or 200-pack of our small unmounted normally open reed switches, rated for up to 100V AC or DC, 1/2 amp of current. Triggering distance will depend on the strength of the magnet. Caveat switcher: the element cannot be mounted vertically and the leads cannot be parallel so leave them bent as they are. They measure just over 1-1/2" long, with a 1/2" element.
|
37213 REED SWITCH |
High Power Relay
A big guy. This chassis-mounted relay is rated for 30A at 300VAC, 15A at 600VAC, 25A at 28VDC, 1 hp at 120VAC, and 2 hp at 240VAC. Coil will draw approx 40mA at 120VAC, and needs at least 80VAC to engage the (2) sets of SPST contacts. Measures 2" x 1-3/8" x 1-1/2" with 1/4" Q/D terminals on the bottom and a 1/8"-32 mounting hole and a mounting tab on one side. Deltrol part number 23063-70
|
37860 BIG RELAY |
Microswitch
Microprice! Black plastic Normally open/normally closed switch is 3/4" x 1/4" x 3/8", with a small button on top, (3) spades on the bottom, and (2) 3/32" dia mounting holes on the side. Ratings unknown. That's all we know!
|
29025 MICROSWITCH |
Relay
This 9 VDC, 120 VAC relay will operate as low as 6 VDC. It is 11/16" x 3/8" x 9/16" thick, and has (4) PC-board leads. Great for hobbies, science projects. SPST.
|
33822 9 VDC RELAY |
Rather Switch Than Fight?
Try our 12VDC SPST rocker switches. The rectangular version is for use at 20A and has a green LED in the paddle. Fits a 1-1/8" x 7/16" hole, and the switch itself is 1-1/4" x 1-11/16" x 1" deep, in black, with quick disconnect terminals. From Calterm®, #40343. The square switch is for use at 25A with an LED in the circular paddle and fits a 5/16" dia hole. The switch itself is 1-1/8" square x 9/16" deep, and quick disconnects on the bottom. From Calterm® #40602.
|
38821 RECTANGULAR SWITCH | |
|
38822 SQUARE SWITCH |
RED LED
An LED that really shines. The red LED is configured with a resistor and works at 9-12 volts. It's held by a 1-5/8" bracket behind a 1-1/4" x 7/16" x 5/16" deep SPST slide switch, and has (2) 4" leads. All ready to roll.
|
32884 9-12 VOLT LED |
Rotary On/Off
Just like your love life?? This switch turns between on and off when the 1/4" dia x 7/8" long shaft is rotated 90°. Rated 120 VAC, 10 amps, it is 1-1/2" x 1" x 1" deep. (2) threaded mounting holes on the face plate and (2) spade connectors complete the picture.
|
29731 ROTARY SWITCH |
Shop by Popular Tags
Click a phrase to shop for products associated with that phrase (AKA "Tag"). More popular tags appear bigger. Learn more »
