These brand-spanking new 12VDC motors are made to move automobile seats but are willing to change. They spin at approx 190 rpm, draw 1.5A no load, and stall at approx 25A. Threaded shaft is at a right angle and is 4-1/8" x 7/16". Shaft thread is non-standard, so treat it as a smooth shaft and mount pulley or gear with a setscrew. Measures 5-5/8" x 2-1/2" x 2-1/2" overall, not counting the shaft, and has power terminals opposite the gearbox with (2) 1/4" mounting holes opposite the shaft.
No self-respecting number cruncher can afford to be seen without one of these fashion classics. We'll pick out (3) black or white vinyl pocket protectors in the traditional 5-1/2" x 3-1/2" size. Order quickly; It's only a question of time before these are seen on the runways in Milan.
Works on all of them except the ones stuck to your eyeballs. Corrosion-Be-Gone is a gel made to remove the schmutz from all types of battery terminals, circuit boards and contacts, on everything from cars to computer boards. Our each is a 0.3 oz jar.
Nice little pulley unit kit includes (1) pulley each at 50, 30, 25 and 20mm and (3) pulleys at 11mm, plus myriad bushings, a small motor, (2) belts and a belt guide, base, mounts and assorted hardware. Includes graphic assembly instructions, plus a couple of rudimentary drawings with suggested projects. It's a mechanical science project waiting for a home.
This small reversible DC motor from JEI runs on 3-6VDC. At 6V it draws 350mA no load and stalls at 1.9A. Spins approx 1000 rpm and approx half that at 3V. Great for science fairs, hobbies and any kind of project that needs spinning. Measures 1-3/16" long x 7/8" dia with a 1/4" x 1/16" shaft and tiny contacts for power that you'd best solder.
Want to trigger something? Start with this honey of a pre-wired, ready-to-go take-out trigger/speed/polarity assembly from a cordless drill. Includes pre-wired IRFZ44N power MOSFET chip mounted on a heat sink. Feed voltage up to 20VDC to the (2) edge connectors at the shorter leads and attach a motor to the longer ones. The CW/off/CCW switch is below the trigger. The entire assembly measures 6" x 2-3/4" x 1-1/4", not counting the 4" leads.
The correct answer is "I don't know; I've never toggled." If, however, you just want to turn something on and off, here's a choice of toggles for your switching delectation. The DPDT toggle is rated for up to 20A at 125VAC and has screw terminals below. Measures 1-1/4" x 1-3/4". No center-off position. The first DPST toggle is rated for 20A at 125VAC or 15A at 250VAC. Screw terminals on the bottom. Measures 1-5/16" x 3/4". The smaller DPST toggle is rated for up to 4A at 125VAC or 2A at 250VAC. Has 3/16" spade terminals on the bottom and measures 1" X 9/16". All the toggles come with switch-plates and mounting nuts.
So you get to pick from our new Nickel-Metal Hydride rechargeable battery bargains. You get a 4-pack of either "AA" 2600 MAH or "AAA" 1000 MAH NiMH batteries, the recommended choice for electronics, cameras, games, cordless phones and toys.
The automotive relay is rated for up to 40A at 12V with a 9-12 VDC coil voltage. Has SPDT contacts for normally open or normally closed operation. The 1" cube has a 5/8" x 13/16" mounting tab and quick-disconnect terminals on the bottom. Made in the USA for Xpress Electrical, part #RL5. Mates perfectly with our 5-pin socket, already wired with 9" leads in black, red, white, yellow and blue to its quick-disconnect sockets, ready for your 1/4" or 7mm spade terminals. Housing is slotted so you can interlock them end to end. Measures 1-1/4" x 1-1/16" x 1" thick.
Our web site always contains everything we have available for sale outside our retail stores. Typically, new items are listed on the site before they get published in our catalog...
Unlike Any Place On Earth
In addition to this fabulous on-line catalog of incredible stuff, American Science & Surplus has three great retail locations. If you're in the neighborhood, please stop by! Store hours may vary. Feel free to call for store hours and directions.