These are medium-base dome-shaped LED light bulbs, and in standard English that’s a light-bulb-shaped LED light bulb with a standard light-bulb screw-in bottom. These draw a stingy 15.5 watts but throw the equivalent of a 100W bulb. Instant-on and dimmable with a 25,000-hour life expectancy, and also suitable for damp conditions. Your only job is to pick 3000K soft white or the 4000K cool white. UL.

Our each here is (5) 5/8” warm white COB LEDs that are insanely bright (think: airport runway) and rated for 200mA at 32VDC. Mounted on PC boards from 3/4” to 1”. Marked for polarity, with solder tabs for power. No lumen rating, but don’t stare at them head-on if you like your retinas because, like we said, they’re awfully bright. And as with all COBs, a heat sink backing is also a good idea.

Like the smartest kid in class, this little PC board is crazy bright with (8) 1/8” dia warm white LED COBs. Clearly marked pads for power inputs. The whole shebang is just 7/8” dia with 3/32” mounting divots. Requires a heat sink and a current-limiting resistor.

Our each is a pack of (10) common cathode 5mm dia red/green/blue LEDs. Clear lens, 20mA rated for 100K hour life. 3V supply will work for all. You also get 100 Ohm and 510 Ohm resistors to step down 5 and 12VDC respectively. Luminous intensity is 4,000 mcd.

These candelabra-base bulbs draw only 2W but put out the equivalent of a 25W incandescent. Will cast a 2700K, yellow-white color at 170 lumens. In a candle-flame shape, blunt top, 3-1/4” tall and not dimmable. Manufacturer says they’ll last 10 times longer than incandescents, which means nine fewer times you’ll stand on the dining room table to change them.

These great little indicator LEDs are wired with an in-line diode on one leg so you can run them with either AC or DC. 12-24 volts works best (do not run them on 120V!) drawing 4mA. You'll get leads between 4" and 9" with quick-disconnect terminals. Because these are pre-wired no fumbling with tiny connectors! You pick yellow or red.

You decide. This panel-mount indicator light has a 5mm red LED in a 5/16” dia x 3/4” deep mount with 47” leads and a 2-pin 5.5mm Molex connector on the other end. Includes wings on the mount to hold it in place. You'll need 20mA at 3VDC for power.

Genesis, the 21st century version. We’re kind of not kidding because this is the guts of a super-intense warm white COB LED light fixture that is so bright it could stand in for the sun. Sorry, we got carried away. Let’s just say it’s insanely bright. Sun-like. Measures 3-3/8” dia with (12) 32VDC COB LED lights, clear or diffused cover lenses (our choice) which may need to be reglued and (4) mounting holes. You add the wiring and a cover. A single LED normally sells for $1.50 each. Do the math. Please mount on a proper heat sink, or your new lamp will go out in a blaze of glory. We recommend a dedicated LED driver or a power supply with a 500mA max output. 

We couldn’t think of any clean jokes for this part, so just add your own. Meanwhile, this little, 1/4” dia, bright white COB LED is mounted on a 3/8” square PC board. Requires 70mA at 9VDC. Our in-house Fire Prevention & Ophthalmology Team suggests a heat sink as well as indirect viewing.

An assortment of (10) COB LEDs between 1/4” and 5/8” dia, mounted on small PC boards with solder pads marked for polarity. Nominally 32VDC 1A. As always with these, use a heat sink!