A really small guy who lives....Whoops! Wrong Chuck. This one is a drill or rotary tool chuck with a 1/8" shank and fits bit sizes #60-#80 to facilitate handling tools with truly small shanks. Very handy in the modeling and electronics worlds.

How many chucks would a key chuck key if a key chuck could key chucks. A key chuck would key...oh forget it. Buy this (4) headed key chuck and know you will have the right size for most popular chucks on tools from Delta, Black & Decker, Bosch and other manufacturers of portable and smaller stationary tools.

Maybe the pilot hole was too small, your driver bit was dull or – sorry – your screw was low-quality. You can’t just sit there stripped and stuck. When you can’t get it in or out, use this (5)-piece screw-extractor set for sizes ranging from 3/16” to 3/4”. The extractors are made of CR-V steel, and all taps have a square drive. No one who screws, even now and then on the weekends, should be without one.

You get a 4-pack of standard 1/4" hex-shaped driver bits that are 6" long for those hard-to-reach screw-heads. Includes a 1/4" slotted driver plus #1 & #2 Phillips and a #2 Robertson in case you're Canadian.

The last set of hole saws you'll ever need. This 10-piece set of diamond-encrusted core drill bits comes in a wooden presentation case (Hey, they've got diamonds on them!) and includes 1/4", 3/8", 1/2", 3/4", 1", 1-1/4", 1-3/8", 1-1/2", 2", and 2-3/8" outer dia. Shanks are 1/4" except the (2) largest, which are 3/8", and all the bits are slotted to blow out dust. Each bit is 1-1/4" deep. Designed for cutting glass, ceramics, porcelain, ceramic and porcelain tile, limestone, slate, marble, granite, stone, fiberglass and other tough stuff. Don't forget to add water (not included) for lubrication.

Get ready to duel the fastest carpenter in the Midwest with this Neocraft® holster for a cordless drill. Fits most drills at 9-3/4” wide x 10-1/4” tall with an open bottom and a wide belt loop. Made of blue and black 600D polyester, with slots for holding (4) drill bits. Get it before some drywall-hanging Frank Miller shows up in town.

This mini version has all of the big guy's abilities on a slightly reduced scale. The bench-top drill press measures approx 15" tall overall on a 6-1/2" x 9" x 1" cast-iron base with a 1-5/16" dia x 11-5/8" tall column. Max working distance is approx 7-1/2". Chuck opens to 5/16", with a spindle travel of 1". It's 120VAC, and has (3) speed ranges, of 5,500, 6,500, and 8,500 rpm. Includes (2) Allen wrenches, chuck key, and, believe it or not, an instruction booklet that is easy to understand.

Please Note: Your entire order will ship standard ground when purchasing this item.

Contact us for expedited shipping information. Thanks!

Put down that hammer and get this Tolsen Tools™ ultra-thin industrial diamond cutting disc. Measures 4 ½" dia and is designed for wet-cutting brick, plaster, tile, granite, marble, ceramics and porcelain. Spins at 13,300 max rpm. 80 M/S with a 20mm arbor and  8mm cutting blade height. As you know by now, Tolsen makes high-quality, professional tools.

This set of (10) diamond hole saws could (extremely theoretically) cut holes in diamonds, but mostly they're for glass, ceramic, marble, slate and tiles. You get 40-grit, diamond-core hole saws at 1/8", 5/32", 13/64", 1/4", 9/32", 5/16", 11/32", 3/8", 7/16" and 1/2" OD, all 2-1/2" long with 1/8" shanks.

Screw around corners or practice your close-order drilling with this right angle chuck adapter for an electric drill. Ratio is 1:1, so the speed matches your drill speed. Has a 3/8” x 1” shank, and a keyless chuck that can be adapted from 3/8” dia to flush. Includes a 2-3/4” right-angle handle that will screw in the left or right side for added leverage. Whole shebang is 5” long.