BEST SELLERS

Move Your Butt

These brand-spanking new 12VDC motors are made to move automobile seats but are willing to change. They spin at approx 190 rpm, draw 1.5A no load, and stall at approx 25A. Threaded shaft is at a right angle and is 4-1/8" x 7/16". Shaft thread is non-standard, so treat it as a smooth shaft and mount pulley or gear with a setscrew. Measures 5-5/8" x 2-1/2" x 2-1/2" overall, not counting the shaft, and has power terminals opposite the gearbox with (2) 1/4" mounting holes opposite the shaft.

accent

CAR SEAT 12VDC GEAR MOTOR

Move Your Butt

These brand-spanking new 12VDC motors are made to move automobile seats but are willing to change. They spin at approx 190 rpm, draw 1.5A no load, and stall at approx 25A. Threaded shaft is at a right angle and is 4-1/8" x 7/16". Shaft thread is non-standard, so treat it as a smooth shaft and mount pulley or gear with a setscrew. Measures 5-5/8" x 2-1/2" x 2-1/2" overall, not counting the shaft, and has power terminals opposite the gearbox with (2) 1/4" mounting holes opposite the shaft.

accent
$14.75 EACH

Fluid Pump

From ET Tech, this series 23 liquid micro-pump draws less than 300mA at 4-6VDC (5VDC nominal) with a liter-per-minute flow rate and up to a 3-foot lift. Not submersible, but suitable for hot-water apps and continuous duty. Measures 1" x 1" dia with a barbed 1/4" right-angle outlet and a 3/8" OD inlet on top. Great for fountains!

accent

4-6VDC MICRO PUMP

Fluid Pump

From ET Tech, this series 23 liquid micro-pump draws less than 300mA at 4-6VDC (5VDC nominal) with a liter-per-minute flow rate and up to a 3-foot lift. Not submersible, but suitable for hot-water apps and continuous duty. Measures 1" x 1" dia with a barbed 1/4" right-angle outlet and a 3/8" OD inlet on top. Great for fountains!

accent
$4.50 EACH
$7.50
-40%

Low Energy Motor

This little 1.5-3VDC motor draws just 15mA no load, which means it's just the ticket for solar-cell applications. At 3VDC it spins approx 600 rpm and stalls at 125mA. Measures 1-1/8" long x 15/16" dia with a 5/16" long x 1/16" dia shaft and 3-1/2" leads.

accent

1-1/2 - 3VDC MOTOR

Low Energy Motor

This little 1.5-3VDC motor draws just 15mA no load, which means it's just the ticket for solar-cell applications. At 3VDC it spins approx 600 rpm and stalls at 125mA. Measures 1-1/8" long x 15/16" dia with a 5/16" long x 1/16" dia shaft and 3-1/2" leads.

accent
$2.95 EACH

Gear Motor

Attention robotics boffins: Here's a nice, powerful 12-24VDC Mabuchi brush motor with a gearbox and pulley attached. At its nominal 24DC, it spins 45rpm, draws 280mA no load, and stalls a 750mA. 7.5 in-lbs of torque and is rated for continuous duty. Has a 3/4" long x 5/16" flattened shaft with a 4-5/8" dia x 5/16" wide (3/16" ID) single-sheave pulley attached, with a matching O-ring. The gearbox measures 2-3/4" x 3" x 9-1/16". The motor measures 1-1/16"dia x 1-5/8" long and comes with 7" leads and a 2-pin Molex connector.

accent

12-24VDC GEAR MOTOR W/PULLEY

Gear Motor

Attention robotics boffins: Here's a nice, powerful 12-24VDC Mabuchi brush motor with a gearbox and pulley attached. At its nominal 24DC, it spins 45rpm, draws 280mA no load, and stalls a 750mA. 7.5 in-lbs of torque and is rated for continuous duty. Has a 3/4" long x 5/16" flattened shaft with a 4-5/8" dia x 5/16" wide (3/16" ID) single-sheave pulley attached, with a matching O-ring. The gearbox measures 2-3/4" x 3" x 9-1/16". The motor measures 1-1/16"dia x 1-5/8" long and comes with 7" leads and a 2-pin Molex connector.

accent
$14.75 EACH

Mini Air Compressor

Nifty device that takes maxi air and squeezes it down into a mini condition. The device is roughly 6-1/2"" long x 6" tall x 4" wide. It has a 10 ft. cord that plugs into an auto lighter socket: i.e. it runs on 12VDC @ 10 amps. Air output is via a 12" hose with a variety of valve adapters for tires, soccer balls, rubber rafts, and just dusting off the environment. Complete with a 0-250 psi gauge. Which should be plenty of pressure to explode a weak bike tire or flimsy beach ball, so please be careful!

accent

COMPACT 12VDC AIR COMPRESSOR

Mini Air Compressor

Nifty device that takes maxi air and squeezes it down into a mini condition. The device is roughly 6-1/2"" long x 6" tall x 4" wide. It has a 10 ft. cord that plugs into an auto lighter socket: i.e. it runs on 12VDC @ 10 amps. Air output is via a 12" hose with a variety of valve adapters for tires, soccer balls, rubber rafts, and just dusting off the environment. Complete with a 0-250 psi gauge. Which should be plenty of pressure to explode a weak bike tire or flimsy beach ball, so please be careful!

accent
$16.85 EACH

DIAPHRAGM AIR PUMP

Great little 12VDC oil-less diaphragm style air pump. For you techies out there it draws 40-300mA, 2.0 Litres/min, 350mm Hg max pressure. These are takeouts but in great condition. Outlet port is 5/32". Overall size 2-3/4" x 1-1/16".

accent

12VDC MINI DIAPHRAGM AIR PUMP

DIAPHRAGM AIR PUMP

Great little 12VDC oil-less diaphragm style air pump. For you techies out there it draws 40-300mA, 2.0 Litres/min, 350mm Hg max pressure. These are takeouts but in great condition. Outlet port is 5/32". Overall size 2-3/4" x 1-1/16".

accent
$3.50 EACH

The Magnificent Seven

Well, the pretty nice seven, anyway, in this 7-blade muffin fan, measuring 4-3/4" sq  x 7/8" and drawing 280mA at 12VDC. Spins approx 2000 rpm and pushes approx 74cfm. Comes with 8" leads and 3/16" mounting holes at the corners. Velleman® part #BLS 12/120.

accent

12VDC SEVEN-BLADE MUFFIN FAN

The Magnificent Seven

Well, the pretty nice seven, anyway, in this 7-blade muffin fan, measuring 4-3/4" sq  x 7/8" and drawing 280mA at 12VDC. Spins approx 2000 rpm and pushes approx 74cfm. Comes with 8" leads and 3/16" mounting holes at the corners. Velleman® part #BLS 12/120.

accent
$5.95 EACH

Submariners’ Alert

This submersible 12VDC water pump is rated for 360gph flow, and up to a 6-foot lift. Draws approx 1A at full power. Input is 13mm ID/17mm OD with a slight lip. Housing measures 1-11/16” square x 2-1/2” on a 3” x 1-5/8” plate with a pair of 5/16” mounting holes and 7-1/2” leads. Also available is the compatible 12VDC 1.5A power supply with a 12+ foot cord with an inline toggle switch approx two feet off the 5.5mm (2.3mm) center-positive female plug. UL.

accent

12VDC WATER PUMP

Submariners’ Alert

This submersible 12VDC water pump is rated for 360gph flow, and up to a 6-foot lift. Draws approx 1A at full power. Input is 13mm ID/17mm OD with a slight lip. Housing measures 1-11/16” square x 2-1/2” on a 3” x 1-5/8” plate with a pair of 5/16” mounting holes and 7-1/2” leads. Also available is the compatible 12VDC 1.5A power supply with a 12+ foot cord with an inline toggle switch approx two feet off the 5.5mm (2.3mm) center-positive female plug. UL.

accent

Wheels Within Wheels

Nice little pulley unit kit includes (1) pulley each at 50, 30, 25 and 20mm and (3) pulleys at 11mm, plus myriad bushings, a 3VDC motor, (2) belts and a belt guide, base, mounts and assorted hardware. Includes graphic assembly instructions, plus a couple of rudimentary drawings with suggested projects. It's a mechanical science project waiting for a home.

accent

PULLEY KIT

Wheels Within Wheels

Nice little pulley unit kit includes (1) pulley each at 50, 30, 25 and 20mm and (3) pulleys at 11mm, plus myriad bushings, a 3VDC motor, (2) belts and a belt guide, base, mounts and assorted hardware. Includes graphic assembly instructions, plus a couple of rudimentary drawings with suggested projects. It's a mechanical science project waiting for a home.

accent
$12.95 EACH

Mabuchi Motor

This torquey take-out 6-24VDC (12VDC nominal) motor draws approx 250mA no load, stalls at 7.2A and spins approx 5700 rpm. Measures 2" x 1-13/32" with a 3/4" x 1/8" flattened shaft and may have a setscrew-mounted coupler that resembles a router bit. Has prewired leads. Mabuchi part no. RS-545SH.

accent

12VDC MABUCHI MOTOR

Mabuchi Motor

This torquey take-out 6-24VDC (12VDC nominal) motor draws approx 250mA no load, stalls at 7.2A and spins approx 5700 rpm. Measures 2" x 1-13/32" with a 3/4" x 1/8" flattened shaft and may have a setscrew-mounted coupler that resembles a router bit. Has prewired leads. Mabuchi part no. RS-545SH.

accent
$3.50 EACH

How About A Little Service?

This tiny servo motor can swing approx 90 degrees in either direction via any of the (3) included servo horns with screws on the 3/16" toothed shaft: a 13/16" long single horn, a 1-5/8" long double horn or the 1-5/8" long double horn with (2) smaller cross horns. Draws between 220 and 650mA at 5VDC, and is rated for 25 oz/in of torque. Measures 7/8" x 1/2" x 1-1/16" deep with a pair of mounting wings with 1/16" bores. Wiring is 5V to red, ground to brown and timing pulses to orange. Use any 1-2ms pulses at 50Hz.

accent

MINI SERVO MOTOR

How About A Little Service?

This tiny servo motor can swing approx 90 degrees in either direction via any of the (3) included servo horns with screws on the 3/16" toothed shaft: a 13/16" long single horn, a 1-5/8" long double horn or the 1-5/8" long double horn with (2) smaller cross horns. Draws between 220 and 650mA at 5VDC, and is rated for 25 oz/in of torque. Measures 7/8" x 1/2" x 1-1/16" deep with a pair of mounting wings with 1/16" bores. Wiring is 5V to red, ground to brown and timing pulses to orange. Use any 1-2ms pulses at 50Hz.

accent
$4.50 EACH

Mabuchi Motor

Little takeout 3-6VDC Mabuchi motors (6VDC nominal) spin approx 4000 rpm and draw 50mA no load. Stall at 300mA and measure 1-1/2" long x 1-1/16" dia with a 1/2” long x 3/32” dia shaft with a 2-sheave 9/16” dia pulley. Sheaves are 1/16” ID. Wired with 2” leads for super easy battery or wall adapter hook up. These were originally from copiers so you'll want to wipe 'em down before use.

accent

3-6VDC MABUCHI MOTOR

Mabuchi Motor

Little takeout 3-6VDC Mabuchi motors (6VDC nominal) spin approx 4000 rpm and draw 50mA no load. Stall at 300mA and measure 1-1/2" long x 1-1/16" dia with a 1/2” long x 3/32” dia shaft with a 2-sheave 9/16” dia pulley. Sheaves are 1/16” ID. Wired with 2” leads for super easy battery or wall adapter hook up. These were originally from copiers so you'll want to wipe 'em down before use.

accent
$0.99 PKG (2)
$2.95
-66%

Submersible Pumps

Here are the ins and outs of submersible pumps for your DIY fountain.These small electric pumps run on 24 VAC (For low energy consumption.) from the included wall outlet adapter, are rated for continuous duty, have (3) suction-cup feet, an adjustable flow control and both a straight and 90° 5/16" tubing adapter. This little pump is roughly 2-5/8" x 1.5" x 2-1/4", has a 6-ft power cord with an in-line switch, and pumps 70 gal/hr @ 1 ft lift. Plug it in and go with the flow. Indoor use only.

accent

SUBMERSIBLE WATER PUMP FOR YOUR DIY FOUNTAIN

Submersible Pumps

Here are the ins and outs of submersible pumps for your DIY fountain.These small electric pumps run on 24 VAC (For low energy consumption.) from the included wall outlet adapter, are rated for continuous duty, have (3) suction-cup feet, an adjustable flow control and both a straight and 90° 5/16" tubing adapter. This little pump is roughly 2-5/8" x 1.5" x 2-1/4", has a 6-ft power cord with an in-line switch, and pumps 70 gal/hr @ 1 ft lift. Plug it in and go with the flow. Indoor use only.

accent
$14.95 EACH

Good Vibrations

Remember those old school vibration football games, or those fantastic days-of-yore vibrating beds in roadside motels? This is like that, a small vibration motor (10mm dia x 2.5mm) that’s touch-sensitive and produces a pleasant buzzy response. Motor has 1-1/4" power leads, draws approx 60mA at 3VDC. Has 0.75g vibe amplitude. Self-adhesive pad on one face. No shaft.

accent

SHAFTLESS VIBRATION MOTOR

Good Vibrations

Remember those old school vibration football games, or those fantastic days-of-yore vibrating beds in roadside motels? This is like that, a small vibration motor (10mm dia x 2.5mm) that’s touch-sensitive and produces a pleasant buzzy response. Motor has 1-1/4" power leads, draws approx 60mA at 3VDC. Has 0.75g vibe amplitude. Self-adhesive pad on one face. No shaft.

accent
$3.95 PKG (2)

MUFFIN BONANZA

Our special Little-Fans-R-Us offering. All these muffin fans are square and all have mounting holes at the corners. Pick and choose the one you want or take a chance on the takeout assortment. (Assortment will not have fans listed in the table above) Please note that the assorted fans are takeouts and will have at least have least two different fans from different manufacturers but maybe the same size. It will be a crap shoot as to what you will receive. 

accent

MUFFIN FAN, 110 VAC, 160mA, 3-3/16" X 1", 2300 RPM, 23 CFM

MUFFIN BONANZA

Our special Little-Fans-R-Us offering. All these muffin fans are square and all have mounting holes at the corners. Pick and choose the one you want or take a chance on the takeout assortment. (Assortment will not have fans listed in the table above) Please note that the assorted fans are takeouts and will have at least have least two different fans from different manufacturers but maybe the same size. It will be a crap shoot as to what you will receive. 

accent
$9.95 EACH

Eight-Tooth Motor

This little 6VDC Mabuchi motor (part #RE-36) draws only 20mA. Spins approx 3000 rpm and measures 1-1/4" x1-1/16" dia with a 3/8" long shaft and a 5/16" dia x 1/4" 8-tooth gear. Runs a tad a squeaky so CJ recommends a dab of machine oil before use.

accent

6VDC MABUCHI MOTOR WITH GEAR

Eight-Tooth Motor

This little 6VDC Mabuchi motor (part #RE-36) draws only 20mA. Spins approx 3000 rpm and measures 1-1/4" x1-1/16" dia with a 3/8" long shaft and a 5/16" dia x 1/4" 8-tooth gear. Runs a tad a squeaky so CJ recommends a dab of machine oil before use.

accent
$3.95 PKG (3)

Science Project Motor & Gearbox

Great for roboticists, too. It's a mighty-mite, this little 6VDC 45 RPM motor with a right-angle gearbox. Draws 13mA, no load, and stalls at 120mA. Output is through (2) double-flattened 1/4" dia x 3/16" long shafts on opposite sides of the white plastic housing, both with 1/16" dia center holes. Measures 1-7/8" x 7/8" overall. Gear ratio is 228:1.

accent

45 RPM GEAR MOTOR

Science Project Motor & Gearbox

Great for roboticists, too. It's a mighty-mite, this little 6VDC 45 RPM motor with a right-angle gearbox. Draws 13mA, no load, and stalls at 120mA. Output is through (2) double-flattened 1/4" dia x 3/16" long shafts on opposite sides of the white plastic housing, both with 1/16" dia center holes. Measures 1-7/8" x 7/8" overall. Gear ratio is 228:1.

accent
$7.50 EACH

Motorette

Nifty little DC motor will run from 1.5 to 12VDC (think: a single AA battery), but at 6VDC will draw only 2mA, stall at 45 and spin approx 400 rpm. At 12VDC it draws close to 3mA, stalls at 90mA and spins approx 950 rpm. Nominal 6VDC. Measures 1-1/4” dia x 7/8” with a striated 1/16” dia x 3/8” shaft. Solder tabs are on the bottom. Great solar project motor.

accent

6VDC SMALL MOTOR

Motorette

Nifty little DC motor will run from 1.5 to 12VDC (think: a single AA battery), but at 6VDC will draw only 2mA, stall at 45 and spin approx 400 rpm. At 12VDC it draws close to 3mA, stalls at 90mA and spins approx 950 rpm. Nominal 6VDC. Measures 1-1/4” dia x 7/8” with a striated 1/16” dia x 3/8” shaft. Solder tabs are on the bottom. Great solar project motor.

accent
$3.50 PKG (4)

Showing 1–18 of 56 results