Looks like a missing part from the Starship Enterprisingly, but it’s really just a dandy little 12VDC piston-action water pump. Originally used for medical purposes. Draws 600mA, has a rate and lift on the low side but should be fine for continuous use for you fountain fans. Measures an L-shaped 5-3/8" x 4-5/8" x 3-1/2", with barbed 1/4” output and 5/32” input diameters.
Looks like a missing part from the Starship Enterprisingly, but it’s really just a dandy little 12VDC piston-action water pump. Originally used for medical purposes. Draws 600mA, has a rate and lift on the low side but should be fine for continuous use for you fountain fans. Measures an L-shaped 5-3/8" x 4-5/8" x 3-1/2", with barbed 1/4” output and 5/32” input diameters.
Our motorman, CJ, called this reversible 12-24VDC motor strange, mostly because it has the power contacts mounted on the face, bracketing the 11/16" x 1/8" mostly striated shaft, and has no mounting brackets. But that shouldn't stop a clever person like you. (Hint: it was probably made to fit into a sleeve of some sort.) At 12VDC, draws 100mA no load, stalls 850mA and spins approx 900 rpm; at 24VDC, draws 150mA, stalls 2.2A and spins approx 1800 rpm. Measures 2-1/4" x 1-13/32" dia.
Our motorman, CJ, called this reversible 12-24VDC motor strange, mostly because it has the power contacts mounted on the face, bracketing the 11/16" x 1/8" mostly striated shaft, and has no mounting brackets. But that shouldn't stop a clever person like you. (Hint: it was probably made to fit into a sleeve of some sort.) At 12VDC, draws 100mA no load, stalls 850mA and spins approx 900 rpm; at 24VDC, draws 150mA, stalls 2.2A and spins approx 1800 rpm. Measures 2-1/4" x 1-13/32" dia.
Muffin fans, pay attention. You pick the "nice" 110 VAC 21W fan from Thermocool, measuring 4-3/4" square x 1-1/2" thick with an offset two-pin power connector, rated for 82-95 cfm and spinning at approx 2600 rpm, with five blades and 3/16" mounting holes at the corners (Mfr part # G12038HA1ST); or the "beastly" 110VAC 36W muffin fan from the same mfr, which blows up to 198 cfm at 2900 rpm and measures 6-3/4" x 6" tall x 2" thick with (2) power terminals on a removable shroud, 5 blades, 5/32" mounting holes on the corners plus a ground lug. Both UL.
Muffin fans, pay attention. You pick the "nice" 110 VAC 21W fan from Thermocool, measuring 4-3/4" square x 1-1/2" thick with an offset two-pin power connector, rated for 82-95 cfm and spinning at approx 2600 rpm, with five blades and 3/16" mounting holes at the corners (Mfr part # G12038HA1ST); or the "beastly" 110VAC 36W muffin fan from the same mfr, which blows up to 198 cfm at 2900 rpm and measures 6-3/4" x 6" tall x 2" thick with (2) power terminals on a removable shroud, 5 blades, 5/32" mounting holes on the corners plus a ground lug. Both UL.
This NOS 12VDC 1A 3-coil brushless servo motor with 36 steps per revolution was for a printer, maybe. Or a scanner, maybe. Whichever, it's mounted on a 2-1/2" x 2" plate with a 3/4" long shaft with a 5/8" dia rubber wheel out one side and a 15-tooth, 2" dia plastic sprocket on the side with the leads. The white lead feeds a Hall effect sensor, then ground, +5V control, and then the three coil leads Samsung P/N 02914900.
This NOS 12VDC 1A 3-coil brushless servo motor with 36 steps per revolution was for a printer, maybe. Or a scanner, maybe. Whichever, it's mounted on a 2-1/2" x 2" plate with a 3/4" long shaft with a 5/8" dia rubber wheel out one side and a 15-tooth, 2" dia plastic sprocket on the side with the leads. The white lead feeds a Hall effect sensor, then ground, +5V control, and then the three coil leads Samsung P/N 02914900.
Our special Little-Fans-R-Us offering. All these muffin fans are square and all have mounting holes at the corners. Pick and choose the one you want or take a chance on the takeout assortment. (Assortment will not have fans listed in the table above) Please note that the assorted fans are takeouts and will have at least have least two different fans from different manufacturers but maybe the same size. It will be a crap shoot as to what you will receive.
Our special Little-Fans-R-Us offering. All these muffin fans are square and all have mounting holes at the corners. Pick and choose the one you want or take a chance on the takeout assortment. (Assortment will not have fans listed in the table above) Please note that the assorted fans are takeouts and will have at least have least two different fans from different manufacturers but maybe the same size. It will be a crap shoot as to what you will receive.
Our Technical Identification Division (CJ) says this is most likely a take-out timer motor from a washing machine. "Probably." Measures just under 2" dia x just under 1" thick, not counting little wings with 5/32" mounting holes and a 10-tooth 5/32" gear. Draws 3W at 115VAC (it has leads but you supply the cord) and spins appx. 8.5RPM. Intermittent duty.
Our Technical Identification Division (CJ) says this is most likely a take-out timer motor from a washing machine. "Probably." Measures just under 2" dia x just under 1" thick, not counting little wings with 5/32" mounting holes and a 10-tooth 5/32" gear. Draws 3W at 115VAC (it has leads but you supply the cord) and spins appx. 8.5RPM. Intermittent duty.
That’s us, a breath of fresh air in the shopping atmosphere. Also, your source for these surplus Swiss-Air™ II Freshener Systems--one with a motion activator, and one without (you pick). Originally took cartridges that freshened the air with cherry, orange, berry, potpourri or other scents. Do they work? Might could, as they say in Nowth Car’lina, but we’re selling them for parts. The wall-mount cases measure 7-3/4" x 3-1/2" x 3-1/8” in cream plastic, with a cover that comes off to reveal a dandy 1.5V motor with a 5-blade fan, and terminals for a D cell battery. Motor is 1” dia x 1” long, shaft is 1/16” dia x 3/8” long, and fan blade is 2-3/8” dia.
That’s us, a breath of fresh air in the shopping atmosphere. Also, your source for these surplus Swiss-Air™ II Freshener Systems--one with a motion activator, and one without (you pick). Originally took cartridges that freshened the air with cherry, orange, berry, potpourri or other scents. Do they work? Might could, as they say in Nowth Car’lina, but we’re selling them for parts. The wall-mount cases measure 7-3/4" x 3-1/2" x 3-1/8” in cream plastic, with a cover that comes off to reveal a dandy 1.5V motor with a 5-blade fan, and terminals for a D cell battery. Motor is 1” dia x 1” long, shaft is 1/16” dia x 3/8” long, and fan blade is 2-3/8” dia.
These small timing motors draw 3W and are just under 2" dia x approx 3/4" thick with mounting wings that have (3) 1/8" holes. You pick: the 11VAC motor that spins 1 rpm CCW with a 3/4" long shaft with an attached 3/4" dia x 1/4" thick 16-tooth gear, 24-pitch and 20-degree pressure angle; or the 24VAC motor that spins 1 rpm CW and has an 8-tooth, 5/16" dia x 11/32" plastic gear, 32-pitch and 20-degree pressure angle.
These small timing motors draw 3W and are just under 2" dia x approx 3/4" thick with mounting wings that have (3) 1/8" holes. You pick: the 11VAC motor that spins 1 rpm CCW with a 3/4" long shaft with an attached 3/4" dia x 1/4" thick 16-tooth gear, 24-pitch and 20-degree pressure angle; or the 24VAC motor that spins 1 rpm CW and has an 8-tooth, 5/16" dia x 11/32" plastic gear, 32-pitch and 20-degree pressure angle.
Little takeout 3-6VDC Mabuchi motors (6VDC nominal) spin approx 4000 rpm and draw 50mA no load. Stall at 300mA and measure 1-1/2" long x 1-1/16" dia with a 1/2” long x 3/32” dia shaft with a 2-sheave 9/16” dia pulley. Sheaves are 1/16” ID. Wired with 2” leads (positive and negative) for super easy battery or wall adapter hook up. A little dusty but incredible for scout projects, classroom robotics projects or making your own army of walking zombies.
Little takeout 3-6VDC Mabuchi motors (6VDC nominal) spin approx 4000 rpm and draw 50mA no load. Stall at 300mA and measure 1-1/2" long x 1-1/16" dia with a 1/2” long x 3/32” dia shaft with a 2-sheave 9/16” dia pulley. Sheaves are 1/16” ID. Wired with 2” leads (positive and negative) for super easy battery or wall adapter hook up. A little dusty but incredible for scout projects, classroom robotics projects or making your own army of walking zombies.
From Maxon Motor, this nice and efficient gear motor is nominally rated at 36VDC, 152 rpm and draws 130mA, but will run with as little as 3V. At 12VDC, it spins approx 28 rpm, draws 75mA no load and stalls at approx 300mA. Measures 2” long x 15/16” dia with a 5/32” x 1/8” flattened shaft, with (3) 1/16” mounting holes on the face and 1-1/2” leads. Made in Switzerland despite not being chocolate or a watch.
From Maxon Motor, this nice and efficient gear motor is nominally rated at 36VDC, 152 rpm and draws 130mA, but will run with as little as 3V. At 12VDC, it spins approx 28 rpm, draws 75mA no load and stalls at approx 300mA. Measures 2” long x 15/16” dia with a 5/32” x 1/8” flattened shaft, with (3) 1/16” mounting holes on the face and 1-1/2” leads. Made in Switzerland despite not being chocolate or a watch.
Because it’s a new take-out fan motor from Welling Service Co., made for air conditioner-humidifiers. Rated for 115VAC, 16W, spins approx 1400 rpm via a 2-1/2” x 5/16” threaded shaft which will most likely have a nut on the end. Has 12” long leads, (2) of which are for a 6uF capacitor (not included). Rotates counter-clockwise and measures 2-5/8" dia x 2-7/16" deep. Has (4) mounting holes on wings. Welling part #YSLB-16-002-001.
Because it’s a new take-out fan motor from Welling Service Co., made for air conditioner-humidifiers. Rated for 115VAC, 16W, spins approx 1400 rpm via a 2-1/2” x 5/16” threaded shaft which will most likely have a nut on the end. Has 12” long leads, (2) of which are for a 6uF capacitor (not included). Rotates counter-clockwise and measures 2-5/8" dia x 2-7/16" deep. Has (4) mounting holes on wings. Welling part #YSLB-16-002-001.
Our sturdy 24VDC 6A linear actuator motor with intermittent duty extends from 56-7/8" to 85-5/8" and has a 337-lb push. The extending shaft is 1-1/4" diameter and the U-joint at the end has a 7/16" ID hole for attaching. Use it to make something go up and down, or in an out. Like an awning, the door on your chicken coop, your holiday yard displays or something in your basement bar, man cave or she shed. Please Note: Your entire order will ship UPS ground with this item and allow a few extra days for shipping time.
Our sturdy 24VDC 6A linear actuator motor with intermittent duty extends from 56-7/8" to 85-5/8" and has a 337-lb push. The extending shaft is 1-1/4" diameter and the U-joint at the end has a 7/16" ID hole for attaching. Use it to make something go up and down, or in an out. Like an awning, the door on your chicken coop, your holiday yard displays or something in your basement bar, man cave or she shed. Please Note: Your entire order will ship UPS ground with this item and allow a few extra days for shipping time.
Little takeout 3-6VDC Mabuchi motors (6VDC nominal) spin approx 4000 rpm and draw 50mA no load. Stall at 300mA and measure 1-1/2" long x 1-1/16" dia with a 1/2” long x 3/32” dia shaft with a 2-sheave 9/16” dia pulley. Sheaves are 1/16” ID. Wired with 2” leads for super easy battery or wall adapter hook up. These were originally from copiers so you'll want to wipe 'em down before use.
Little takeout 3-6VDC Mabuchi motors (6VDC nominal) spin approx 4000 rpm and draw 50mA no load. Stall at 300mA and measure 1-1/2" long x 1-1/16" dia with a 1/2” long x 3/32” dia shaft with a 2-sheave 9/16” dia pulley. Sheaves are 1/16” ID. Wired with 2” leads for super easy battery or wall adapter hook up. These were originally from copiers so you'll want to wipe 'em down before use.