If you can find a slimmer toolkit for your bicycle, we’d really love to see it. Our 30-in-1 tool is 5” long when closed (a touch over 8-1/2” when open), 1-1/2” wide and a half-inch deep. Always a half-inch deep—and it’s made of black Titanium-coated steel! The Cycle-On’s (30) different essential bike tools include (12) wrenches (5mm-17mm), (5) Allen wrenches (3mm-8mm), (2) spoke clips and (2) tire levers, a cutter/stripper/crimper, a file, a ¼” bit driver, magnetic bit driver, medium Phillips driver, bottle opener and a ruler in both inches and centimeters. Even includes a case. Don’t ride without one!
If you can find a slimmer toolkit for your bicycle, we’d really love to see it. Our 30-in-1 tool is 5” long when closed (a touch over 8-1/2” when open), 1-1/2” wide and a half-inch deep. Always a half-inch deep—and it’s made of black Titanium-coated steel! The Cycle-On’s (30) different essential bike tools include (12) wrenches (5mm-17mm), (5) Allen wrenches (3mm-8mm), (2) spoke clips and (2) tire levers, a cutter/stripper/crimper, a file, a ¼” bit driver, magnetic bit driver, medium Phillips driver, bottle opener and a ruler in both inches and centimeters. Even includes a case. Don’t ride without one!
These brand-spanking new 12VDC motors are made to move automobile seats but are willing to change. They spin at approx 190 rpm, draw 1.5A no load, and stall at approx 25A. Threaded shaft is at a right angle and is 4-1/8" x 7/16". Shaft thread is non-standard, so treat it as a smooth shaft and mount pulley or gear with a setscrew. Measures 5-5/8" x 2-1/2" x 2-1/2" overall, not counting the shaft, and has power terminals opposite the gearbox with (2) 1/4" mounting holes opposite the shaft. If you're looking for a power supply, we've got one. Just snip the plug of this regulated switching power supply and wire it up.
These brand-spanking new 12VDC motors are made to move automobile seats but are willing to change. They spin at approx 190 rpm, draw 1.5A no load, and stall at approx 25A. Threaded shaft is at a right angle and is 4-1/8" x 7/16". Shaft thread is non-standard, so treat it as a smooth shaft and mount pulley or gear with a setscrew. Measures 5-5/8" x 2-1/2" x 2-1/2" overall, not counting the shaft, and has power terminals opposite the gearbox with (2) 1/4" mounting holes opposite the shaft. If you're looking for a power supply, we've got one. Just snip the plug of this regulated switching power supply and wire it up.
From ET Tech, this series 23 liquid micro-pump draws less than 300mA at 4-6VDC (5VDC nominal) with a liter-per-minute flow rate and up to a 3-foot lift. Not submersible, but suitable for hot-water apps and continuous duty. Measures 1" x 1" dia with a barbed 1/4" right-angle outlet and a 3/8" OD inlet on top. Great for fountains!
From ET Tech, this series 23 liquid micro-pump draws less than 300mA at 4-6VDC (5VDC nominal) with a liter-per-minute flow rate and up to a 3-foot lift. Not submersible, but suitable for hot-water apps and continuous duty. Measures 1" x 1" dia with a barbed 1/4" right-angle outlet and a 3/8" OD inlet on top. Great for fountains!
No self-respecting number cruncher can afford to be seen without one of these fashion classics. We'll send you (3) classic white vinyl pocket protectors in the traditional 5-1/2" x 3-1/2" size. The front flap is blank so you can add your own name, business or drawing of your favorite Star Trek character. Order quickly; It's only a question of time before these are seen on the runways in Milan.
No self-respecting number cruncher can afford to be seen without one of these fashion classics. We'll send you (3) classic white vinyl pocket protectors in the traditional 5-1/2" x 3-1/2" size. The front flap is blank so you can add your own name, business or drawing of your favorite Star Trek character. Order quickly; It's only a question of time before these are seen on the runways in Milan.
Attention robotics boffins: Here's a nice, powerful 12-24VDC Mabuchi brush motor with a gearbox and pulley attached. At its nominal 24DC, it spins 45rpm, draws 280mA no load, and stalls a 750mA. 7.5 in-lbs of torque and is rated for continuous duty. Has a 3/4" long x 5/16" flattened shaft with a 4-5/8" dia x 5/16" wide (3/16" ID) single-sheave pulley attached, with a matching O-ring. The gearbox measures 2-3/4" x 3" x 9-1/16". The motor measures 1-1/16"dia x 1-5/8" long and comes with 7" leads and a 2-pin Molex connector.
Attention robotics boffins: Here's a nice, powerful 12-24VDC Mabuchi brush motor with a gearbox and pulley attached. At its nominal 24DC, it spins 45rpm, draws 280mA no load, and stalls a 750mA. 7.5 in-lbs of torque and is rated for continuous duty. Has a 3/4" long x 5/16" flattened shaft with a 4-5/8" dia x 5/16" wide (3/16" ID) single-sheave pulley attached, with a matching O-ring. The gearbox measures 2-3/4" x 3" x 9-1/16". The motor measures 1-1/16"dia x 1-5/8" long and comes with 7" leads and a 2-pin Molex connector.
These large momentary SPDT push-button switches are rated 10A at 125/250VAC and are mounted to a 2-7/16"dia lens plate with a 1-1/8" long x 15/16 - 2 shaft that comes with a plastic washer and nut. There's also an internal 12V 3W replaceable indicator bulb. Needs 3" of rear clearance. You pick a red, green or yellow lens.
These large momentary SPDT push-button switches are rated 10A at 125/250VAC and are mounted to a 2-7/16"dia lens plate with a 1-1/8" long x 15/16 - 2 shaft that comes with a plastic washer and nut. There's also an internal 12V 3W replaceable indicator bulb. Needs 3" of rear clearance. You pick a red, green or yellow lens.
Great for roboticists, too. It's a mighty-mite, this little 6VDC 45 RPM motor with a right-angle gearbox. Draws 13mA, no load, and stalls at 120mA. Output is through (2) double-flattened 1/4" dia x 3/16" long shafts on opposite sides of the white plastic housing, both with 1/16" dia center holes. Measures 1-7/8" x 7/8" overall. Gear ratio is 228:1.
Great for roboticists, too. It's a mighty-mite, this little 6VDC 45 RPM motor with a right-angle gearbox. Draws 13mA, no load, and stalls at 120mA. Output is through (2) double-flattened 1/4" dia x 3/16" long shafts on opposite sides of the white plastic housing, both with 1/16" dia center holes. Measures 1-7/8" x 7/8" overall. Gear ratio is 228:1.
The correct answer is "I don't know; I've never toggled." If, however, you just want to turn something on and off, here's a choice of toggles for your switching delectation. The DPDT toggle is rated for up to 20A at 125VAC and has screw terminals below. Measures 1-1/4" x 1-3/4". No center-off position. The first DPST toggle is rated for 20A at 125VAC or 15A at 250VAC. Screw terminals on the bottom. Measures 1-5/16" x 3/4". The smaller DPST toggle is rated for up to 4A at 125VAC or 2A at 250VAC. Has 3/16" spade terminals on the bottom and measures 1" X 9/16". All the toggles come with switch-plates and mounting nuts.
The correct answer is "I don't know; I've never toggled." If, however, you just want to turn something on and off, here's a choice of toggles for your switching delectation. The DPDT toggle is rated for up to 20A at 125VAC and has screw terminals below. Measures 1-1/4" x 1-3/4". No center-off position. The first DPST toggle is rated for 20A at 125VAC or 15A at 250VAC. Screw terminals on the bottom. Measures 1-5/16" x 3/4". The smaller DPST toggle is rated for up to 4A at 125VAC or 2A at 250VAC. Has 3/16" spade terminals on the bottom and measures 1" X 9/16". All the toggles come with switch-plates and mounting nuts.