Now you can have a good, strong hook without drilling any holes. This plated magnetic hook sticks to any ferrous metal surface via a 2" dia alnico magnet with a 10-12 pound pull. Handy gadget to hold a tool, towel, broom or key ring (and if the ring is too heavy, consider throwing away the keys to your 1983 Chevy, and maybe a few more). The 3/4" long J-hooks have threaded ends and are removable. Our each is a package of (2).

A rubber grommet, 7/8" dia x 11/16" thick, with a brass insert that forms a flange over one face and lines about 3/4" of the length of the 1/4" dia bore. Use it as a grommet, a shock mount, or both. With  a brass wire hanger that is set under the insert flange and extends 1" to the side. The hanger is bent to hold a 1/4" dia wire.

A fatal yoga position? Crocodile moves? Nope, just a shiny steel snap hook, 3-1/2" long with a 3/8" ID, attached to a 3/4” ID swivel, the better to hook your keys on whatever you hook your keys on.

1-7/8" dia. green, brown or orange hard plastic balls with a 1-1/4" ID x 1-1/2" deep hole on one side. Use them as slippery chair feet, as knobs on the ends of levers or tops of canes or even as protective caps for sharp pole ends. The tapered inner veins will provide a tight friction fit. You get an assortment of colors.

Brass L-shaped shoulder hooks (Why aren’t they elbow hooks?) are handy to have around. Each has a thread about half as long as the hook itself, and a small plate that fits against the wall. You get (2) packages, for a total of (6) 1” hooks, or (4) 1–1/2” hooks.

Large plastic hook, pointed on one end, blunt on the other. We have no idea what it was made for. Some suggest a meat hook in a pet food factory, which the shape supports. But the red or white plastic suggests not. Maybe it is for veggies? A loyal reader is convinced that it goes over a door and bananas are hung from it. Sounds good to us. The blunt end is shaped to hang over a square beam, 1-1/4" or so thick. The other pointy end, when the hook is so hung, will be 3" from the beam top, and will point out 3" and up @ about 15°. The whole is made of 3/8" dia plastic rod. You figure out what to do with it.

In big quantities. And dirt cheap. The dark brown plastic, 1-11/16" squares with one corner cut off at a 45° angle are approx 1/16" thick, with a raised center square, a 9/16" hole in the center, and peel-off really-self-adhesive backing. For art projects, air vents for snake cages, wall plates for cable runs, or something. Please.

Our each is a set of (42) assorted zinc-plated steel clamps with rubber insulation, for wiring, hoses, etc. You get (20) at 1/4"; (8) at 5/16"; (6) at 3/8" and (4) each at 1/2" and 5/8", all marked with the size and in a plastic storage box.

This zinc-plated carbon steel clevis grab hook is rated Grade 43 with a 2,600-lb load limit (that's about a Mini Cooper hatchback). Measures 3" long x 1-7/8" at the wide part x 1/2" at the thick part, with a 3/8" axle held with a cotter pin. Clearance from hood to axle is also 3/8".

These black steel placard mounts are perfect for restaurant specials, place cards, or more permanent signage. Two very tight 1" tall clips are mounted on an approx 2" x 11/16" base with good'n'sticky self-adhesive foam on the bottom. Also drilled with (2) small holes if you want to nail or screw through the foam.