These brand-spanking new 12VDC motors are made to move automobile seats but are willing to change. They spin at approx 190 rpm, draw 1.5A no load, and stall at approx 25A. Threaded shaft is at a right angle and is 4-1/8" x 7/16". Shaft thread is non-standard, so treat it as a smooth shaft and mount pulley or gear with a setscrew. Measures 5-5/8" x 2-1/2" x 2-1/2" overall, not counting the shaft, and has power terminals opposite the gearbox with (2) 1/4" mounting holes opposite the shaft.
This little 1.5-3VDC motor draws just 15mA no load, which means it's just the ticket for solar-cell applications. At 3VDC it spins approx 600 rpm and stalls at 125mA. Measures 1-1/8" long x 15/16" dia with a 5/16" long x 1/16" dia shaft and 3-1/2" leads.
This torquey take-out 6-24VDC (12VDC nominal) motor draws approx 250mA no load, stalls at 7.2A and spins approx 5700 rpm. Measures 2" x 1-13/32" with a 3/4" x 1/8" flattened shaft and may have a setscrew-mounted coupler that resembles a router bit. Has prewired leads. Mabuchi part no. RS-545SH.
Attention robotics boffins: Here's a nice, powerful 12-24VDC Mabuchi brush motor with a gearbox and pulley attached. At its nominal 24DC, it spins 45rpm, draws 280mA no load, and stalls a 750mA. 7.5 in-lbs of torque and is rated for continuous duty. Has a 3/4" long x 5/16" flattened shaft with a 4-5/8" dia x 5/16" wide (3/16" ID) single-sheave pulley attached, with a matching O-ring. The gearbox measures 2-3/4" x 3" x 9-1/16". The motor measures 1-1/16"dia x 1-5/8" long and comes with 7" leads and a 2-pin Molex connector.
This tiny servo motor can swing approx 90 degrees in either direction via any of the (3) included servo horns with screws on the 3/16" toothed shaft: a 13/16" long single horn, a 1-5/8" long double horn or the 1-5/8" long double horn with (2) smaller cross horns. Draws between 220 and 650mA at 5VDC, and is rated for 25 oz/in of torque. Measures 7/8" x 1/2" x 1-1/16" deep with a pair of mounting wings with 1/16" bores. Wiring is 5V to red, ground to brown and timing pulses to orange. Use any 1-2ms pulses at 50Hz.
Here are the ins and outs of submersible
pumps for your DIY fountain.These small electric pumps run on 24 VAC
(For low energy consumption.) from the included wall outlet adapter, are
rated for continuous duty, have (3) suction-cup feet, an adjustable
flow control and both a straight and 90° 5/16" tubing adapter. This
little pump is roughly 2-5/8" x 1.5" x 2-1/4", has a 6-ft power cord
with an in-line switch, and pumps 70 gal/hr @ 1 ft lift. Plug it in and
go with the flow. Indoor use only.
Well, the pretty nice seven, anyway, in this 7-blade muffin fan, measuring 4-3/4" sq x 7/8" and drawing 280mA at 12VDC. Spins approx 2000 rpm and pushes approx 74cfm. Comes with 8" leads and 3/16" mounting holes at the corners. Velleman® part #BLS 12/120.
Great for roboticists, too. It's a mighty-mite, this little 6VDC 45 RPM motor with a right-angle gearbox. Draws 13mA, no load, and stalls at 120mA. Output is through (2) double-flattened 1/4" dia x 3/16" long shafts on opposite sides of the white plastic housing, both with 1/16" dia center holes. Measures 1-7/8" x 7/8" overall. Gear ratio is 228:1.
This 3-phase brushless 12VDC motor from Nidec draws 2.5A max through the red and black leads with what we think are coil taps, and Hall effect outputs through the other (4) leads. Measures 36mm (1.4") dia x 40mm (1.6") long with a 4mm (0.16") dia x 19mm (0.75") shaft with a removable cam. Includes a spec sheet.
For store hours, phone and directions, click here.
Or View Our Latest Printed Catalog Online
Our web site always contains everything we have available for sale outside our retail stores. Typically, new items are listed on the site before they get published in our catalog...
Unlike Any Place On Earth
In addition to this fabulous on-line catalog of incredible stuff, American Science & Surplus has three great retail locations. If you're in the neighborhood, please stop by! Store hours may vary. Feel free to call for store hours and directions.