You don’t even have to be rude about it because this is a set of (3) small cleaning brushes for removing rust, paint, grime and schmutz in general. They’re 7” long with plastic handles with 45-degree offset heads. You’ll get (1) each with stainless steel, brass and stiff nylon bristles. The brush area is 1-1/2” x 1/4” on all of them.

Or forever compared to sandpaper, anyway. These sponges from 3M have a microfine grit and measure 5-1/2" x 4-1/2" x 3/16".  We'll send you (3) so your kids can help too. And they’re made in England, where the royal grit is always microfine.

Super-long Q-type tips are for people who don't want to get too close to their ears. Actually, these are tech swabs with cotton tops and wooden sticks for lab work, so leave your ears out of it. Good for other body parts, though, and for too many craft applications to list. You get (3) packs, for a total of (300) 6-1/4" long fuzzy-topped sticks.

Here's a set of (5) tiny embedded-diamond files, just in case you have some tiny embedded diamonds that need filing. They are 3-1/8" long OA, with rubber handles. The file portions are 1 mm to 2 mm wide, with assorted pointed-round, pointed-flat, and blunt-flat tips at 150 grit.

Life too dull? You need a whetstone, and this one, while it's not a stone at all, is a big improvement. It's a 4-sided diamond sharpening block, 6" long x 2-1/2" on a side, sitting snugly in a wooden holder with slip-resistant rubber feet. The sides are 200, 300, 400 and 600 grit, so you can work your way up to a razor's edge on knives, chisels, or anything that needs a little edge.

So you won't want to lose this 6-piece set of diamond burrs. They're on 1/4" shanks, and are 2-1/4" to 2-3/8" long OA, with approx 1/2" dia heads. The set includes one of each shape: cylinder, round-end cylinder, round, egg, inverse cone and pointed cone. All are #40 grit. Incredibly handy for those tough jobs!

It’s a whetstone for sharpening knives and no, it doesn’t need to be wet to use. (“Whet” means to hone.) This one is small, pocket knife-size. Some folks use a little mineral oil, but that isn’t necessary either. This stone is 220-grit, and measures 3-7/8" x 1" x 1/2". Lay it on a wet paper or cloth towel, so it doesn’t slip, then pull your blade across it a dozen times on each side with the edge tipped to a about 22-1/2-degree angle or less, which you approximate by standing it up at 90 degrees, then tipping it halfway to 45, then halfway again.

We’ve got a lovely bunch of sanding sponges. And they can be yours for less than you’d drop in a fast food drive-thru. Most are from 3M and Norton Abrasives®, and they range from coarse to fine grit in sizes from 4" x 2-3/4" x 1" to 4-7/8" x 3-1/2" x 1". We’ll pick a couple for you, OK?

For those hard-to-reach contours, nothing beats a wet/dry sanding sponge. This one measures 4" x 2-3/4" x 1" and is marked "Very Fine/Fine, Tres Fin/Fin, Muy Fino/Fino," which we make to be approx 220 grit, although we didn't count them.

Who doesn’t like a polished look? Your better metalworkers and welders use these flap discs for a shiny finished look after the grinding wheels are done. Our each is a trio of 3” zirconium oxide-coated discs, (1) each at 40-, 60- and 80-grit, and they come with an “R” type holder and a 1/4” shank. Billy, our zirconium oxide polishing buff (yes, of course that pun is intentional) says they do their best work at approx 13K rpm.